Selfhosted @lemmy.world cakeofhonor @lemmy.world 5 mo. ago

Help with IPv6

My ISP recently made IPv6 available and I'm trying to figure out how to make it work with my network. The setup I have is an OPNsense box connected to my ISP's router and I'm using it to isolate my homelab from the rest of the network. However, the machines on my OPNsense LAN aren't being assigned IPv6 addresses that allow them to connect to the internet.

I can ping IPv6 sites from my OPNsense box and I see that it's being assigned a /64 prefix from the ISP router. If I use my laptop to connect to my ISP's router, I can visit IPv6 sites just fine as well. My devices in the OPNsense LAN also have IPv6 addresses and can ping each other using IPv6 but not the internet.

Are there special settings that I need to set for OPNsense to make this setup work? I've tried reading up on the different modes like SLAAC but I'm not quite grasping the concepts.

You're viewing a single thread.

16 comments

I'm no expert on IPv6 but here's how I did it on my OPNsense box:

Activate IPv6 on your WAN interface (probably already done)

Activate IPv6 on the LAN interface, use Track interface on IPv6, track the WAN interface and choose a prefix ID like 0x1

Activate DHCPv6 under Services -> ISC DHCPv6 for your LAN interface (you can shorten the range like ::eeee to ::ffff, you don't have to type the full IP)

Activate Router advertisments under Services -> Router Advertisments for your LAN interface (set Advertisments to Managed and Priority to High

After that your DHCP server should serve public IPv6 addresses inside of your prefix and clients should be able to connect to the internet.

A few notes:

Don't forget to add an allow rule for IPv6 on your LAN as well if you only have one for IPv4

Repeat the steps above for every VLAN you have, always use a different prefix ID

You don't have to use NAT rules with IPv6 anymore and can just directly add a regular firewall rule to WAN with the target IP and port and you are done

Make sure you don't have any of the various "Disable IPv6" toggles enabled, there's a few in the firewall settings and general settings for example
- I'll try this when I get a chance. Off the top of my head, why did you set the prefix to 0x1? I was under the impression that it only needs to be set if there are multiple vlans and what are your rules for the WAN side of the firewall? My LAN interface is only getting an LLA so maybe it's being blocked from communicating with the ISP router.
  
  Off the top of my head, why did you set the prefix to 0x1? I was under the impression that it only needs to be set if there are multiple vlans
  
  I have multiple VLANs, 0x1 is my LAN and 0x10 is my DMZ for example. I then get IP addresses abcd:abcd:a01::abcd in my LAN and abcd:abcd:a10::bcdf in my DMZ.
  
  However, I get a /56 from my ISP wich gets subnetted into /64. I heard it's not ideal to subnet a /64 but you might want to double check what you really got.
  
  what are your rules for the WAN side of the firewall?
  
  Only IPv4 + IPv6 ICMP, the normal NAT rules for IPv4 and the same rules for IPv6 but as regular rule instead of NAT rule.
  
  My LAN interface is only getting an LLA so maybe it’s being blocked from communicating with the ISP router.
  
  If you enable DHCPv6 in your network your firewall should be the one to hand out IP addresses, your ISP assigns your OPNsense the prefix and your OPNsense then subnets them into smaller chunks for your internal networks.
  
  It is possible to do it without DHCPv6 but I didn't read into it yet since DHCPv6 does exactly what I want it to do.
  
  Prefix ID of 0x1 means "Use the first prefix available in the block as a /64 for the LAN". Essentially your ISP probably gave you a /48, /56, or /60. The firewall is giving prefix IDs to all of the /64s you can fit inside of one of these and allocating them numbers 1 through whatever. Each LAN you have can have its own prefix ID. A /60 has 16 /64 networks that you can subnet it into.

You've viewed 16 comments.