Do people actually tune their printer for each new roll of filament?
Do people actually tune their printer for each new roll of filament?
I see a lot of people claim they tune/calibrate their printer any time they use a new spool of filament. But does anyone actually do this? It feels like a waste of time when filament is so consistent, even between brands. I can understand doing it for specialty rolls, but for basic pla? Seems unnecessary
You're viewing a single thread.
Not for each new roll of filament, but I am relatively new (less than 1 month) and with the same roll I have some prints failing. Mostly because they detatch from the bed (Material is PETG, on an Ender 3 Max Neo). I've tried a lot of things already:
- Different nozzle temps
- Z axis offset calibration
- Cleaning the print-bed
- Leveling the print-bed (including the screws and the A4 paper trick)
- Heated bed vs. non-heated
- Printer placed in an enclosure to prevent drafts
So far it seems to go alright, but I still get detatching prints occasionally, or deforming mid-print. It's kind of frustrating :(
Oh, you poor thing. I made the same mistake. I know, I know, PETG logically makes the most sense - no fumes, higher temp tolerance, cheap - but save yourself weeks of misery and stick with PLA or PLA Plus/Pro/+ for a few months. PETG is a special beast. For all the shit PLA gets, it's not that bad and MUCH easier to learn printing with.
PETG is more viscous and sticky, and generally requires its own z-offset tuning and retraction tweaks. On top of that, it needs juuuuust enough heat to melt the Bowden tube, which happens to make it really tempting to pop a few prints. I'm pretty sure I invented new curse words while trying to clean out that mess.
PETG was the second filament I tried. The first was Silk PLA. It's PLA, but shiny, no biggie, right? Don't learn on Silk PLA either. Completely different set of problems. Silk PLA to PLA is like Frosted Fakes to cake frosting.
Just my $0.02. I know I was all excited to print mods for the printer right away, but I've ended up replacing all those mods with MUCH better ones 6 months later. Good luck!
Edit: Forgot to mention, make sure you use glue stick or hairspray on the bed. PETG will bond strong enough to take some of the bed surface with it!
So I've essentially started printing on a higher difficulty? Guess I'll switch to PLA when the PETG runs out and change profiles in the slicer to PLA
Yes, you're printing on Hard Mode. PETG is weird at first, but easy-ish later on. Some veterans tend to treat it like no big deal, but it can be a real stumbling block for some. I know it took me a while.
I had the same problem with my CR-10. The issue was that the weak original bed springs were too weak to hold the bed. The vibrations of the printer allowed it to move, causing the first layer to not adhere very well. I also had filaments get moisture after a week or two.
When people say upgrade the Creality bed springs, they aren't kidding. PLA is forgiving enough on the first layer, but upgrading those bedsprings was necessary for me to print PETG. I made them stiffer by adding 5-6x washers on each post to pre-compress the springs. This makes them much stiffer and stay put.
I also bought a filament dryer. I put a new roll of PETG in the dryer and put it in continuous mode at 55°, and print PETG directly from the dryer.
I still have to print PETG pretty slowly compared to PLA or ASA (my favorite material).
To OP's original question: I do a full tuning of PETG with a new maker/roll. PETG is a co-polymer. Each manufacturer could have a different amount of glycol on the PET chain, or even a different distribution (e.g. ABABABAB copolymers behave differently than AAAABBBB copolymers even though both are 50% B). Colorants can also affect behavior.
PLA I really don't tune. I add 5-10 degrees when I'm printing quickly. That's about it. I recently was printing a spacer out of the last bit of a PLA+ roll I had. The filament ran out and the printer halted. I loaded a matte PLA to finish (I slowed the printer down and bumped the temp up manually by 5 degrees since this matte stuff has layer adhesion issues), and it also ran out before the print was done. So I loaded a roll of transparent PLA that I bought 9-10 years ago (and was stored in an attic for 2 years) and is very brittle, and it printed just fine. The print looks strange (tan to matte terra cotta to transparent purple) but works great.
Oh thanks for pointing out the bed springs! That does sound like something that can be happening, since they seem to slowly 'unwind' causing the bed to lower. I'll add some washers; thanks for the tip!
I did this more as a temporary fix. There are lots of sellers of stiffer spring sets or silicone spacers for Creality printers online. There are also several models on thingiverse for printing your own spacers.