can't fix RAM voltage on a Gigabyte B450 Aorus Elite
can't fix RAM voltage on a Gigabyte B450 Aorus Elite
I have a Ryzen 5 1600AF (Zen+) and 2x 8 GB DDR4 3600 HyperX. when I select XMP1, it says 1.35V in the profile. however, when I boot Strelec WinPE USB (I'm on Fedora, I really don't want to install windows just so I can run HWINFO), install all drivers and launch HWINFO64 it says 1.2V. so I enter BIOS again, go to Voltages and enter 1.35 manually instead of auto. no change, still reads 1.2V. the BIOS side screen shows 1.35 after reboot.
I've found an unresolved thread somewhere with the same problem for my board. I'm on latest BIOS.
am I missing something, is there some additional setting I need to switch so it registers? the BIOS setup is hella confusing and borderline stupid, e.g. enabling virtualization required turning on SMP (how am I supposed to guess what that is?!) that's located in the "Frequency" subsection (wtf?!).
Here's a Toms Hardware thread> where someone had a similar issue. It may help point you in the right direction.
If it's running stable at the correct speed, does it matter what voltage it runs on?
it is not, presently it runs at 2400. setting it to 3600 causes it to fail to boot. occasionally it boots fine, but various apps don't work (Firefox can't open, Geekbench crashes, etc.). also, there's the known issue of freezing after waking from sleep, for which the fixed voltage is supposedly the fix.
If you open the sensors part of HWINFO there should be a
DIMMvoltage from the motherboard, that's a live reading, what does that say?I'm on Fedora
Here's a few alternatives to HWINFO I've used:
- CPU-X (has a GUI, and is probably the most like HWINFO but still different)
- lm-sensors (might require a custom profile for your motherboard, but can provide live temp/fan/voltage sensor readings)
- dmidecode (built in, can read the data off the dimm, but doesn't read sensors directly)
Edit: Just realised I have that motherboard, and it's probably why XMP stopped being stable. I'll look into it on Monday.
Edit 2: From memory to use lm-sensors you need to use an updated it87 driver for both chips to appear, I can provide a sensors profile on Monday.
CPU-X doesn't list RAM voltages. sensors lists a buncha stuff (none labeled as DDR voltage) but all at 1.2V. dmidecode also lists 1.2V for all items, but I've read that its data is unreliable. I've tried already all the listed options (and then some) and that's why I tried WinPE, as HWINFO64 is supposed to have methods to reliably determine RAM voltage.
Diagnostics
dmidecode output:
Memory Device Array Handle: 0x000B Error Information Handle: 0x0011 Total Width: 64 bits Data Width: 64 bits Size: 8 GB Form Factor: DIMM Set: None Locator: DIMM 0 Bank Locator: P0 CHANNEL A Type: DDR4 Type Detail: Synchronous Unbuffered (Unregistered) Speed: 3000 MT/s Manufacturer: Kingston Serial Number: 0B0672F9 Asset Tag: Not Specified Part Number: KHX3600C17D4/8GX Rank: 1 Configured Memory Speed: 3000 MT/s Minimum Voltage: 1.2 V Maximum Voltage: 1.2 V Configured Voltage: 1.2 V Memory Technology: DRAM Memory Operating Mode Capability: Volatile memory Firmware Version: Unknown Module Manufacturer ID: Bank 2, Hex 0x98 Module Product ID: Unknown Memory Subsystem Controller Manufacturer ID: Unknown Memory Subsystem Controller Product ID: Unknown Non-Volatile Size: None Volatile Size: 8 GB Cache Size: None Logical Size: Nonesensors:
it8792-isa-0a60 Adapter: ISA adapter in0: 1.79 V (min = +0.00 V, max = +2.78 V) in1: 1.18 V (min = +0.00 V, max = +2.78 V) in2: 1.02 V (min = +0.00 V, max = +2.78 V) +3.3V: 3.38 V (min = +0.00 V, max = +5.56 V) in4: 1.20 V (min = +0.00 V, max = +2.78 V) in5: 1.04 V (min = +0.00 V, max = +2.78 V) in6: 2.78 V (min = +0.00 V, max = +2.78 V) ALARM 3VSB: 3.36 V (min = +0.00 V, max = +5.56 V) Vbat: 3.33 Vbios:
dmidecode and sensors output are from XMP2 (3000 MT/s, also 1.35V) as I can't boot the OS at XMP1, but when I could the output was the same.
Unless gigabyte changed it in a newer revision, that motherboard has 2 it87 chips, but you need a newer driver to see both in sensors.