Why can't they use the excess energy to make the train go again?
They were asking for a ride. She speaks Ukrainian. I'm guessing she wasn't bothered by it.
I might have crossed my wires, it was probably just a forum post I misread. I happened to have new ceramic burrs so I went ahead and installed them.
I got closer to a perfect pull this morning after adjusting the right lever! Unfortunately I'm out of that coffee now so the process restarts with the next bag.
New ceramic burrs.
I typically use light roast beans, apparently ceramic is better there.
Went through the hyperalignment procedure and got close but not perfect. Had to move on and get it back together at some point.
Works the same, just inline. And this grinder has two
Is this comparing total number of visitors per year to inhabitants?
If so, it's a misleading graphic because visitors only stay for a week or two.
Free solo*
But with a harness full of gear for extra weight reasons
And gloves because less grip == good?
We water by soaking the plants in the tub, then letting them sit on towels before going back on the shelf. A bit tedious but only has to be done every 1-2 months.
True with crimps, not as important with pinches, which is what this mug is
This is how I did it with my old board. My new board has a jumper to toggle between powering via USB and not.
When the only tool you have is a deep lifelong understanding of computational language, everything starts to look like a hypergraph.
How does our universe work? Scientist Stephen Wolfram opens up his ongoing Wolfram Physics Project to a global effort. His team will livestream work in progress, post working materials, release software tools and hold educational programs.
Just learned about this. A long read, but really interesting.
Cisco Webex.
You think teams or zoom are annoying? This is much worse. The worst part is with some default meeting settings, a loud chime would play every time someone joined. People kept this on for meetings of 300+ people, then they started talking over the beeps once "the popcorn slowed down."
Extraction is heavily controlled by amount of water, temperature, grind size, and time.
To get an under extracted brew, you would use more water with a shorter brew time with a course grind at a lower temperature. This should give you something that's sour, weak, watery, with a thin mouthfeel.
Overextraction would be the opposite. Boiling water in a preheated brewing device, fine grind, less water, steeped for a longer time. This should taste dark, bitter, burnt, strong, with a soupy grimy mouthfeel.
You can make one cup of each at the extremes to taste the difference, and then use that information to tweak your regular brew one variable at a time. Look up the coffee compass to help understand what you're tasting and which direction to move.
My wife wanted a plant stand because our succulents had gone wild. She showed me an Amazon item, and I thought, “$60? I can build that myself.” So I did. It only cost $100 and took an entire weekend.
Update to my previous post: https://lemmy.ca/post/7236274
I don't know why I even bother opening the settings app
My table saw needs to be mobile so I can put it away against the wall when I’m not using it. The existing products are expensive or don’t fully swivel. I came up with a cheap and convenient solution using flip-down casters.
To reduce dust in my garage, I sealed my table saw and attached a shop vac with a bucket cyclone. Sealing the saw redirects the shop vac’s limited airflow to where it’s needed most: the throat plate. This makes the shop vac a reasonable alternative to an expensive and bulky dust collector. In the pr...
It's wild how similar woodworking and 3d printing are.
- Get a 3d printer
- Print things for the 3d printer
With woodworking
- Get a table saw
- Make things for the table saw
Now I can mix and match
Model: https://www.printables.com/model/205258-featherboard-with-replaceable-heads-m6
Had minimal clearance between these overhead shelves and the garage door, and the perfect light spacing was a few inches away from the cross bars. So I designed these snap fit brackets to offset the lights inline.
The lights make a huge difference, much more pleasant to work in the garage.
What I learned:
- there is some sag because the screws aren't at the top of the bracket. I would add a tab that protrudes on the side so I could add a screw higher.
- the screw face split on layer lines on a few of these. Still works but not perfect, so I would make the screw face thicker.
Also printed cable management clips
