Night lights that detect light levels are probably flickering so fast that it just appears to be on
Night lights that detect light levels are probably flickering so fast that it just appears to be on
Ok so I got this idea not while showering, but because I'm very high. The story does come from my bathroom though! I have a night light in my bathroom, and I was looking at the night light as I turned off the bathroom light. I'm a big nerd so I remembered that the things that detect light levels are actually diodes wired in reverse. I thought it would be funny to make it flicker by reflecting the light back on the diode, but it didn't work. That's when I had this realization
Modern night lights won't have this happen, as they have a built-in "buffer" to prevent rapid on/off cycles like that.
But I do remember having an old night light when I was younger, probably from the late 80s, that you could make flicker by putting your hand in front of the bulb so that the light reflects back onto the sensor, effectively turning it into a very fast Useless Machine.
Constant voltage LEDs use something called Pulse Width Modulation, or PWM, to simulate dimmed lights. That's basically what you're describing.
I knew that dimmable LEDs exist now, but I didn't know why they worked. Cool!
Like some motors they operate best at a certain duty cycle.
The issue with some really cheap ones is that it’s obvious.
It’s also why, if you’re so inclined at Christmas time, led string lights on trees are hard to photograph since you’ll catch some of them on while others are off at the time of the photo.
That's how all ac powered lights work because the current is constantly alternating.
I was going to protest this, but then I started looking into how ac is converted to dc and realized that it would be cheaper to just let the diodes run on ac.
oh shit, my stoned ass wasn't prepared for this
Indeed, older bulbs work in both directions and the voltage fluctuation isn't visible in the light emitted, because the thermal mass of the filament smooths out the alternating current into a continuous glow.
But LEDs will flicker unless the AC is rectified and smoothed out. Cheap lights will just not come with the circuitry to do this, as you can just hook up the diode directly, the only drawback being it will only emit light some of time. 60Hz is slow enough that you will notice it, however. Especially with movement, it makes reality look like it's running at 60fps.
Even when rectified, unless a capacitor is added to the circuit, LEDs will flicker. AC merely rectified will still have the voltage hitting zero 60 times a second, otherwise.
Alternating current is back-and-forth vs on-and-off. The filaments aren’t rated for rapid strobing, which is why you can easily burn them out by just using a light switch to flicker them too much.
While that's true, in between the voltage spike in either direction there is a moment of equilibrium that is equivalent to "off".
This moment lasts for too short a time to matter, as the voltage goes up and down smoothly in the pattern of a sine wave, meaning the time spent in the true "off" state is infinitesimally small, not 1/60 of a second as the frequency would suggest.
But even then the filaments temperature does fluctuate with the flips in voltage. It again just doesn't matter, as it becomes sufficiently energised again before it even cools enough to stop glowing.
Cheap LEDs stop glowing much quicker than a filament, which is why they can flicker even when the AC is rectified into DC, if done without a capacitor to smooth out the voltage.
Bro juat reinvented pwm thats why lights can look weird when flashes are close to a factor of the framerate.
ok but, are you high?
You need to research how optical sensors actually work.
From this source:
A phototransistor is a type of bipolar transistor in which the base-collector junction comes into light. This results in the same behavior of a photodiode
I'm high and I just wanted to post something low effort that I thought was funny. I know it's more complex than the way I described it.
Edit: also, diodes are directional. Saying that a photodiode is "a diode wired in reverse" should be the first sign that I know more than what I'm actually saying. All diodes are capable of reacting to light, a photodiode exploits and amplifies the principle.
Now take an LED light that has the exact opposite frequency to your local power grid and hold it onto the sensor. The night light won't know what hit it!